CRC ALU H.T. HIGH TEMPERATURE ALUMINIUM COATING

CRC ALU H.T. HIGH TEMPERATURE ALUMINIUM COATING
CRC ALU H.T. HIGH TEMPERATURE ALUMINIUM COATING
Price And Quantity
  • Piece/Pieces
  • 500
  • Piece/Pieces
  • 100.00-
    Product Description

    CRC ALU H.T. HIGH TEMPERATURE ALUMINIUM COATING

    GENERAL DESCRIPTION

    High temperature aluminium coating.

    A high temperature paint based on silicone resins and active aluminium pigments.Alu H.T. is designed to build a hard lasting finish that will not burn off, chip or peel at high temperatures.
    FEATURES

    • High thermal stability: resists temperatures up to 600°C.
    • Excellent coverage.
    • High durability.
    • Quick drying at room temperature.
    • Very good resistance to temperature fluctuations.
    • Good weather stability. Although some loss of gloss can be noticed after extended exposure.
    • Totally lead and chromate free.
    • No chlorinated and no aromatic solvents.
    • Aerosols use dimethylether (DME) propellant for controlled application and film properties.
    APPLICATIONS
    • Stove pipes
    • Stoves
    • Heaters
    • Kilns
    • Incinerators
    • Chimneys
    • Exhaust manifolds
    • Headers
    • Engines
    • Ovens
    • Steam pipes
    DIRECTIONS
    • Shake aerosol can very well for at least one minute after agitator ball is free. Stir or mix bulk product well to obtain a homogeneous dispersion. Repeat frequently while using.
    • Apply to a clean, degreased, dry surface for best results. Remove rust and scale with a wire brush.
    • Apply in light, even coats; best results are obtained with 2 lighter rather than 1 heavy coat. Additional coats can be applied after 15-30 minutes.
    • Complete curing occurs during use, typically after 1 h @ 200°C or 45 min. @ 250°C.
    • When spraying is finished, clean aerosol valve by turning can upside down and pressing button until only propellant escapes. If clogging occurs, remove button and clean orifice with fine wire.
    • Do not use on energised equipment. Use in well ventilated area.
    • A safety data sheet (MSDS) according EU directive 93/112 is available for all CRC products.
    TYPICAL(*) PRODUCT DATA (without propellant)
    • Appearance : mat aluminium finish
    • Resin type : silicone
    • Pigment type : non-leafing aluminium
    • Specific gravity (@ 20°C)
      • aerosol : 0,99
      • bulk : 1,11
    • Flash point (solvents)
      • aerosol : -4°C
      • bulk : 42°C
    • Coverage (30 mm, dry)
      • aerosol : approx. 2,7 m2/can (400 ml)
      • bulk : TBD
    • Drying times
    • To touch : 15 min @ 20°C (45% RH)
    • To : 24 h @ 20°C (45% RH)
    • To complete cure : 1 h @ 200°C
    • Recommended film thickness : 25-30 µm
    • Thinner / cleaner : M.E.K., acetates
    • Dry film properties (on degreased metal)
    • Heat resistance (ASTM D-2485-68)
    • Method 1 (24 h cont.) : 600°C
    • Method 2 (cycling) : 635°C
    • Adhesion on steel (NFT 30038) : 0/1
    • Flexibility : pass (after heating to 600°C, 6 mm mandrel, visual)
    PACKAGING
    • aerosol : 12 x 400 ml
    • bulk : 750 ml  
    Trade Information
    • 5000 Per Week
    • 5-7 Days
      Contact Us

      15, Dhamanwala Complex, Opp. Batliboi, Gidc Cross Road, Pandesara, Surat Gujarat India +918037302043
      Phone :+918037302043